X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/475fe28a6a039803d280266e29e755a603d1dfe7..c1ac69960f6c08393233fe99fe44a1c99373e6df:/doc/doc-txt/NewStuff diff --git a/doc/doc-txt/NewStuff b/doc/doc-txt/NewStuff index 4a2739188..a4ac7e5ad 100644 --- a/doc/doc-txt/NewStuff +++ b/doc/doc-txt/NewStuff @@ -1,4 +1,4 @@ -$Cambridge: exim/doc/doc-txt/NewStuff,v 1.34 2005/04/06 14:03:53 ph10 Exp $ +$Cambridge: exim/doc/doc-txt/NewStuff,v 1.41 2005/05/17 09:53:34 ph10 Exp $ New Features in Exim -------------------- @@ -9,6 +9,79 @@ updated when there is a relatively large batch of changes). The doc/ChangeLog file contains a listing of all changes, including bug fixes. +Exim version 4.52 +----------------- + +TF/01 Support for checking Client SMTP Authorization has been added. CSA is a + system which allows a site to advertise which machines are and are not + permitted to send email. This is done by placing special SRV records in + the DNS, which are looked up using the client's HELO domain. At this + time CSA is still an Internet-Draft. + + Client SMTP Authorization checks are performed by the ACL condition + verify=csa. This will fail if the client is not authorized. If there is + a DNS problem, or if no valid CSA SRV record is found, or if the client + is authorized, the condition succeeds. These three cases can be + distinguished using the expansion variable $csa_status, which can take + one of the values "fail", "defer", "unknown", or "ok". The condition + does not itself defer because that would be likely to cause problems + for legitimate email. + + The error messages produced by the CSA code include slightly more + detail. If $csa_status is "defer" this may be because of problems + looking up the CSA SRV record, or problems looking up the CSA target + address record. There are four reasons for $csa_status being "fail": + the client's host name is explicitly not authorized; the client's IP + address does not match any of the CSA target IP addresses; the client's + host name is authorized but it has no valid target IP addresses (e.g. + the target's addresses are IPv6 and the client is using IPv4); or the + client's host name has no CSA SRV record but a parent domain has + asserted that all subdomains must be explicitly authorized. + + The verify=csa condition can take an argument which is the domain to + use for the DNS query. The default is verify=csa/$sender_helo_name. + + This implementation includes an extension to CSA. If the query domain + is an address literal such as [192.0.2.95], or if it is a bare IP + address, Exim will search for CSA SRV records in the reverse DNS as if + the HELO domain was e.g. 95.2.0.192.in-addr.arpa. Therefore it is + meaningful to say, for example, verify=csa/$sender_host_address - in + fact, this is the check that Exim performs if the client does not say + HELO. This extension can be turned off by setting the main + configuration option dns_csa_use_reverse = false. + + If a CSA SRV record is not found for the domain itself, then a search + is performed through its parent domains for a record which might be + making assertions about subdomains. The maximum depth of this search is + limited using the main configuration option dns_csa_search_limit, which + takes the value 5 by default. Exim does not look for CSA SRV records in + a top level domain, so the default settings handle HELO domains as long + as seven (hostname.five.four.three.two.one.com) which encompasses the + vast majority of legitimate HELO domains. + + The dnsdb lookup also has support for CSA. Although dnsdb already + supports SRV lookups, this is not sufficient because of the extra + parent domain search behaviour of CSA, and (as with PTR lookups) + dnsdb also turns IP addresses into lookups in the reverse DNS space. + The result of ${lookup dnsdb {csa=$sender_helo_name} } has two + space-separated fields: an authorization code and a target host name. + The authorization code can be "Y" for yes, "N" for no, "X" for explicit + authorization required but absent, or "?" for unknown. + +PH/01 The amount of output produced by the "make" process has been reduced, + because the compile lines are often rather long, making it all pretty + unreadable. The new style is along the lines of the 2.6 Linux kernel: + just a short line for each module that is being compiled or linked. + However, it is still possible to get the full output, by calling "make" + like this: + + FULLECHO='' make -e + + The value of FULLECHO defaults to "@", the flag character that suppresses + command reflection in "make". When you ask for the full output, it is + given in addition to the the short output. + + Version 4.51 ------------ @@ -140,6 +213,46 @@ PH/07 $acl_verify_message is now set immediately after the failure of a Previously, $acl_verify_message was set only while expanding "message" and "log_message" when a very denied access. +PH/08 The redirect router has two new options, sieve_useraddress and + sieve_subaddress. These are passed to a Sieve filter to specify the :user + and :subaddress parts of an address. Both options are unset by default. + However, when a Sieve filter is run, if sieve_useraddress is unset, the + entire original local part (including any prefix or suffix) is used for + :user. An unset subaddress is treated as an empty subaddress. + +PH/09 Quota values can be followed by G as well as K and M. + +PH/10 $message_linecount is a new variable that contains the total number of + lines in the header and body of the message. Compare $body_linecount, + which is the count for the body only. During the DATA and + content-scanning ACLs, $message_linecount contains the number of lines + received. Before delivery happens (that is, before filters, routers, and + transports run) the count is increased to include the Received: header + line that Exim standardly adds, and also any other header lines that are + added by ACLs. The blank line that separates the message header from the + body is not counted. Here is an example of the use of this variable in a + DATA ACL: + + deny message = Too many lines in message header + condition = \ + ${if <{250}{${eval: $message_linecount - $body_linecount}}} + + In the MAIL and RCPT ACLs, the value is zero because at that stage the + message has not yet been received. + +PH/11 In a ${run expansion, the variable $value (which contains the standard + output) is now also usable in the "else" string. + +PH/12 In a pipe transport, although a timeout while waiting for the pipe + process to complete was treated as a delivery failure, a timeout while + writing the message to the pipe was logged, but erroneously treated as a + successful delivery. Such timeouts include transport filter timeouts. For + consistency with the overall process timeout, these timeouts are now + treated as errors, giving rise to delivery failures by default. However, + there is now a new Boolean option for the pipe transport called + timeout_defer, which, if set TRUE, converts the failures into defers for + both kinds of timeout. A transport filter timeout is now identified in + the log output. Version 4.50