X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/2cbb4081528ed0f71b474f88cf36a55fb0717863..944a9c55d5b7d3d50ea8b8fabfb7a7be5ca8693f:/doc/doc-txt/ChangeLog

diff --git a/doc/doc-txt/ChangeLog b/doc/doc-txt/ChangeLog
index f23bd7e04..764485175 100644
--- a/doc/doc-txt/ChangeLog
+++ b/doc/doc-txt/ChangeLog
@@ -1,4 +1,4 @@
-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.300 2006/02/14 15:11:43 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.311 2006/02/22 15:08:20 ph10 Exp $
 
 Change log file for Exim from version 4.21
 -------------------------------------------
@@ -166,6 +166,65 @@ PH/32 In November 2003, the code in Exim that added an empty Bcc: header when
       needed by RFC 822 but not by RFC 2822 was commented out. I have now
       tidied the source and removed it altogether.
 
+PH/33 When a queue run was abandoned because the load average was too high, a
+      log line was always written; now it is written only if the queue_run log
+      selector is set. In addition, the log line for abandonment now contains
+      information about the queue run such as the pid. This is always present
+      in "start" and "stop" lines but was omitted from the "abandon" line.
+
+PH/34 Omit spaces between a header name and the colon in the error message that
+      is given when verify = headers_syntax fails (if there are lots of them,
+      the message gets confusing).
+
+PH/35 Change the default for dns_check_names_pattern to allow slashes within
+      names, as there are now some PTR records that contain slashes. This check
+      is only to protect against broken name servers that fall over on strange
+      characters, so the fact that it applies to all lookups doesn't matter.
+
+PH/36 Now that the new test suite is complete, we can remove some of the
+      special code in Exim that was needed for the old test suite. For example,
+      sorting DNS records because real resolvers return them in an arbitrary
+      order. The new test suite's fake resolver always returns records in the
+      same order.
+
+PH/37 When running in the test harness, use -odi for submitted messages (e.g.
+      bounces) except when queue_only is set, to avoid logging races between
+      the different processes.
+
+PH/38 Panic-die if .include specifies a non-absolute path.
+
+PH/39 A tweak to the "H" retry rule from its user.
+
+JJ/03 exipick: Removed parentheses from 'next' and 'last' calls that specified
+      a label.  They prevented compilation on older perls.
+
+JJ/04 exipick: Refactored code to prevent implicit split to @_ which caused
+      a warning to be raised on newish perls.
+
+JJ/05 exipick: Fixed bug where -bpc always showed a count of all messages
+      on queue.  Changes to match documented behaviour of showing count of
+      messages matching specified criteria.
+
+PH/40 Changed the default ident timeout from 30s to 5s.
+
+PH/41 Added support for the use of login_cap features, on those BSD systems
+      that have them, for controlling the resources used by pipe deliveries.
+
+PH/42 The content-scanning code uses fopen() to create files in which to put
+      message data. Previously it was not paying any attention to the mode of
+      the files. Exim runs with umask(0) because the rest of the code creates
+      files with open(), and sets the required mode explicitly. Thus, these
+      files were ending up world-writeable. This was not a big issue, because,
+      being within the spool directory, they were not world-accessible. I have
+      created a function called modefopen, which takes an additional mode
+      argument. It sets umask(777), creates the file, chmods it to the required
+      mode, then resets the umask. All the relevant calls to fopen() in the
+      content scanning code have been changed to use this function.
+
+PH/43 If retry_interval_max is set greater than 24 hours, it is quietly reset
+      to 24 hours. This avoids potential overflow problems when processing G
+      and H retry rules. I suspect nobody ever tinkers with this value.
+
 
 Exim version 4.60
 -----------------