X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/06b43f1b7f7319445d4a71b9a60e3f2f144cf7a2..4341239037d5aac10b785f60f0e78570ab4ddebb:/doc/doc-docbook/spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 79bdb24e5..d030a8411 100644
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -14972,6 +14972,7 @@ See also the &'Policy controls'& section above.
 .row &%dsn_advertise_hosts%&         "advertise DSN extensions to these hosts"
 .row &%ignore_fromline_hosts%&       "allow &""From ""& from these hosts"
 .row &%ignore_fromline_local%&       "allow &""From ""& from local SMTP"
+.row &%limits_advertise_hosts%&      "advertise LIMITS to these hosts"
 .row &%pipelining_advertise_hosts%&  "advertise pipelining to these hosts"
 .row &%pipelining_connect_advertise_hosts%& "advertise pipelining to these hosts"
 .row &%prdr_enable%&                 "advertise PRDR to all hosts"
@@ -16556,6 +16557,18 @@ has been built with LDAP support.
 
 
 
+.new
+.option limits_advertise_hosts main "host list&!!" *
+.cindex LIMITS "suppressing advertising"
+.cindex "ESMTP extensions" LIMITS
+This option can be used to suppress the advertisement of the SMTP
+LIMITS extension (RFC 9422) to specific hosts.
+If permitted, Exim as a servier will advertise in the EHLO response
+the limit for RCPT commands set by the &%recipients_max%& option (if it is set)
+and the limit for MAIL commands set by the &%smtp_accept_max_per_connection%&
+option.
+,wen
+
 .option local_from_check main boolean true
 .cindex "&'Sender:'& header line" "disabling addition of"
 .cindex "&'From:'& header line" "disabling checking of"
@@ -17459,16 +17472,26 @@ or if the message was submitted locally (not using TCP/IP), and the &%-bnq%&
 option was not set.
 
 
-.option recipients_max main integer 50000
+.option recipients_max main integer&!! 50000
 .cindex "limit" "number of recipients"
 .cindex "recipient" "maximum number"
-If this option is set greater than zero, it specifies the maximum number of
+If the value resulting from expanding this option
+is set greater than zero, it specifies the maximum number of
 original recipients for any message. Additional recipients that are generated
 by aliasing or forwarding do not count. SMTP messages get a 452 response for
 all recipients over the limit; earlier recipients are delivered as normal.
 Non-SMTP messages with too many recipients are failed, and no deliveries are
 done.
 
+.new
+For SMTP message the expansion is done after the connection is
+accepted (but before any SMTP conversation) and may depend on
+the IP addresses and port numbers of the connection.
+&*Note*&: If an expansion is used for the option,
+care should be taken that a resonable value results for
+non-SMTP messages.
+.wen
+
 .cindex "RCPT" "maximum number of incoming"
 &*Note*&: The RFCs specify that an SMTP server should accept at least 100
 RCPT commands in a single message.
@@ -25356,6 +25379,13 @@ over a single TCP/IP connection. If the value is zero, there is no limit.
 For testing purposes, this value can be overridden by the &%-oB%& command line
 option.
 
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a MAILMAX value,
+and either TLSS is in use or was not advertised,
+that value also constrains the result of this option.
+.wen
+
 
 .option dane_require_tls_ciphers smtp string&!! unset
 .cindex "TLS" "requiring specific ciphers for DANE"
@@ -25932,6 +25962,14 @@ each set of addresses is treated independently, and
 so can cause parallel connections to the same host if &%remote_max_parallel%&
 permits this.
 
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a RCPTMAX value,
+and either TLSS is in use or was not advertised,
+that value also constrains the result of this option
+and no parallel connections will be caused on meeting the RCPTMAX limit.
+.wen
+
 
 .option message_linelength_limit smtp integer 998
 .cindex "line length" limit
@@ -25963,6 +26001,14 @@ If the connection is DANE-enabled then this option is ignored;
 only messages having the domain used for the DANE TLSA lookup are
 sent on the connection.
 
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a RCPTDOMAINMAX value,
+and either TLSS is in use or was not advertised,
+this option is regarded as being false.
+.wen
+
+
 .option port smtp string&!! "see below"
 .cindex "port" "sending TCP/IP"
 .cindex "TCP/IP" "setting outgoing port"
@@ -30719,6 +30765,10 @@ and the &%acl_smtp_mime%& ACLs.
 The &%acl_smtp_dkim%& ACL is available only when Exim is compiled with DKIM support
 enabled (which is the default).
 
+If, for a specific message, an ACL control
+&*dkim_disable_verify*&
+has been set, this &%acl_smtp_dkim%& ACL is not called.
+
 The ACL test specified by &%acl_smtp_dkim%& happens after a message has been
 received, and is executed for each DKIM signature found in a message.  If not
 otherwise specified, the default action is to accept.
@@ -41550,8 +41600,11 @@ Exim's DKIM implementation allows for
 .olist
 Signing outgoing messages: This function is implemented in the SMTP transport.
 It can co-exist with all other Exim features
-(including transport filters)
-except cutthrough delivery.
+(including transport filters) except cutthrough delivery.
+.new
+However, signing options may not depend on headers modified by
+routers, the transport or a transport filter.
+.wen
 .next
 Verifying signatures in incoming messages: This is implemented by an additional
 ACL (acl_smtp_dkim), which can be called several times per message, with