X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/475fe28a6a039803d280266e29e755a603d1dfe7..cfe75fc353d701560110e26fe3b1a6bab8cae2b4:/doc/doc-txt/ChangeLog

diff --git a/doc/doc-txt/ChangeLog b/doc/doc-txt/ChangeLog
index 8f648575b..0470f493b 100644
--- a/doc/doc-txt/ChangeLog
+++ b/doc/doc-txt/ChangeLog
@@ -1,4 +1,4 @@
-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.114 2005/04/06 14:03:53 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.124 2005/04/27 10:00:18 ph10 Exp $
 
 Change log file for Exim from version 4.21
 -------------------------------------------
@@ -168,6 +168,75 @@ PH/27 $acl_verify_message is now set immediately after the failure of a
       Previously, $acl_verify_message was set only while expanding "message"
       and "log_message" when a very denied access.
 
+PH/28 Modified OS/os.c-Linux with
+
+        -#ifndef OS_LOAD_AVERAGE
+        +#if !defined(OS_LOAD_AVERAGE) && defined(__linux__)
+
+      to make Exim compile on kfreebsd-gnu. (I'm totally confused about the
+      nomenclature these days.)
+
+PH/29 Installed patch from the Sieve maintainer that adds the options
+      sieve_useraddress and sieve_subaddress to the redirect router.
+
+PH/30 In these circumstances:
+        . Two addresses routed to the same list of hosts;
+        . First host does not offer TLS;
+        . First host accepts first address;
+        . First host gives temporary error to second address;
+        . Second host offers TLS and a TLS session is established;
+        . Second host accepts second address.
+      Exim incorrectly logged both deliveries with the TLS parameters (cipher
+      and peerdn, if requested) that were in fact used only for the second
+      address.
+
+PH/31 When doing a callout as part of verifying an address, Exim was not paying
+      attention to any local part prefix or suffix that was matched by the
+      router that accepted the address. It now behaves in the same way as it
+      does for delivery: the affixes are removed from the local part unless
+      rcpt_include_affixes is set on the transport.
+
+PH/32 Add the sender address, as F=<...>, to the log line when logging a
+      timeout during the DATA phase of an incoming message.
+
+PH/33 Sieve envelope tests were broken for match types other than :is. I have
+      applied a patch sanctioned by the Sieve maintainer.
+
+PH/34 Change 4.50/80 broke Exim in that it could no longer handle cases where
+      the uid or gid is negative. A case of a negative gid caused this to be
+      noticed. The fix allows for either to be negative.
+
+PH/35 ACL_WHERE_MIME is now declared unconditionally, to avoid too much code
+      clutter, but the tables that are indexed by ACL_WHERE_xxx values had been
+      overlooked.
+
+PH/36 The change PH/12 above was broken. Fixed it.
+
+PH/37 Exim used to check for duplicate addresses in the middle of routing, on
+      the grounds that routing the same address twice would always produce the
+      same answer. This might have been true once, but it is certainly no
+      longer true now. Routing a child address may depend on the previous
+      routing that produced that child. Some complicated redirection strategies
+      went wrong when messages had multiple recipients, and made Exim's
+      behaviour dependent on the order in which the addresses were given.
+
+      I have moved the duplicate checking until after the routing is complete.
+      Exim scans the addresses that are assigned to local and remote
+      transports, and removes any duplicates. This means that more work will be
+      done, as duplicates will always all be routed, but duplicates are
+      presumably rare, so I don't expect this is of any significance.
+
+      For deliveries to pipes, files, and autoreplies, the duplicate checking
+      still happens during the routing process, since they are not going to be
+      routed further.
+
+PH/38 Installed a patch from Ian Freislich, with the agreement of Tom Kistner.
+      It corrects a timeout issue with spamd. This is Ian's comment: "The
+      background is that sometimes spamd either never reads data from a
+      connection it has accepted, or it never writes response data. The exiscan
+      spam.[ch] uses a 3600 second timeout on spamd socket reads, further, it
+      blindly assumes that writes won't block so it may never time out."
+
 
 A note about Exim versions 4.44 and 4.50
 ----------------------------------------